16×20 Canvas Stretching Tutorial by John O’Keefe Jr.

This 16×20 canvas stretching tutorial focuses on a giclee print on canvas. However, the steps can also be applied to any medium-sized canvas, whether raw, primed, or painted. I provide tutorials like this for free because I feel that all of us should be able to enjoy creating art without all the “extra costs” that many would charge for this level of information.


16×20 CANVAS STRETCHING – MATERIALS AND TOOLS

Step 1

16 x 20 Canvas Stretching - Step 1 - Assemble all materials

Before starting, Assemble all materials and tools for the 16×20 canvas stretching tutorial.

  1. Cloth Work Surface
  2. Giclee Print (not shown)
  3. Pre-Made Stretcher Bars
  4. Square Ruler
  5. Mallet
  6. Small Hammer
  7. Flathead Screwdriver
  8. Staple Gun
  9. 1/4″ Staples
  10. Tape Measure
  11. Canvas Pliers
  12. Pencil

CANVAS STRETCHING – APPLY GLUE TO STRETCHER BARS

NOTE: (Steps 2 through 4 are optional)

Step 2

16 x 20 Canvas Stretching - Step 2 Optional - Elmer's Carpenter's Wood Glue

     We will use Elmer’s Wood Glue to bond the stretcher bars ends together. Because we are using pre-made stretcher bars that come ready to assemble, we may need to sand rough edges that have resulted from the cutting tools used during the manufacturing process.


Step 3

16 x 20 Canvas Stretching - Step 3 Optional - Apply Elmer's to stretcher bar corner

Apply a small amount of glue to each end, as shown. Repeat this for each stretcher bar before continuing to the next step.


Step 4

16 x 20 Canvas Stretching - Step 4 Optional - Spread glue using fingers

Using your finger, spread the glue around each cut end’s surface, as shown. Repeat this for the remaining stretcher bars.

CANVAS STRETCHING – ASSEMBLE THE STRETCHER BARS

Step 5

16 x 20 Canvas Stretching - Step 5 - Assembly first two stretcher bars

Begin mating the stretcher bars.


Step 6

16 x 20 Canvas Stretching - Step 6 - Ensure stretcher bars have a snug fit

Make sure that you fully seat the stretcher bar ends. If you see a gap along the seam where the ends meet, you have not fully mated the two bars.


Step 7

16 x 20 Canvas Stretching - Step 7 - Assemble remaining stretcher bars

In this view, all four stretcher bars are shown mated together. However, we must ensure that all four corners of this assembly are square before the glue sets. (i.e., A, B, C, & D)


Step 8

16 x 20 Canvas Stretching - Step 8 - Wipe off excess glue if it was applied

If you used glue (as shown in steps 2 through 4), wipe off any excess glue that has squeezed out while mating the stretcher bars.


Step 9

16 x 20 Canvas Stretching - Step 9 - Measure diagonal corners (A-B)

Measure the distance between corner A and corner B.


Step 10

16 x 20 Canvas Stretching - Step 10 - Measure opposite diagonal corners (C-D)

Measure the distance between corner C and corner D.

Compare the two distances against each other. If the distances AB and CD are equal, you are square. If they are not equal, you are not square.

(In our example, distance AB was 0.125 inches larger than distance CD, and we need to make adjustments as shown in steps 11 and 12.)


Step 11

16 x 20 Canvas Stretching - Step 11 - If not square adjust using mallet

While firmly holding the stretcher bar assembly, tap the corner with a mallet with the largest measurement.

(In our example, we will tap corner A.)


Step 12

16 x 20 Canvas Stretching - Step 12 - Recheck squareness using a square

Recheck all corners to make sure they are square. We can use the earlier tape measure or square ruler method shown here.

Hold the square ruler as shown and check that both inside edges of the ruler run flush along the surface of each stretcher bar. You are not square if the ruler lifts off on one side (not running flush along the entire surface). Repeat this check on all the remaining corners. If your stretcher bar assembly is square, you are ready to start the canvas mounting process.


Step 13

16 x 20 Canvas Stretching - Step 13 - Sand stretcher bar corners

Using light-grade sandpaper, gently remove any rough or broken wood from corners.


Step 14

16 x 20 Canvas Stretching - Step 14 - Inspect that no jagged edges exist

Ensure the corners are thoroughly sanded, and no rough edges remain.

CANVAS STRETCHING – PREPARE FOR STAPLING

Step 15a

16 x 20 Canvas Stretching - Step 15 - Soft cloth workspace

Before laying down your giclee canvas print, make sure there are no debris or wood pieces (that may have fallen off during stretcher bar assembly) that could damage the printed surface. A soft cloth work surface minimizes the chances of causing minor scratches to your giclee canvas print.


Step 15b

16 x 20 Canvas Stretching - Step 15 - Clean work surface and inspect canvas print for damage

Lay down your print (face up) and make a final close examination to ensure it has no damage.


Step 16

16 x 20 Canvas Stretching - Step 16 - Put canvas print face down onto work surface

Turn over your giclee print at this point, so the image is face down. You are now ready to position your stretcher bar assembly.


Step 17

16 x 20 Canvas Stretching - Step 17 - Place assembled stretcher bars onto canvas print

Place your stretcher bar assembly over your giclee canvas print as shown.

16×20 CANVAS STRETCHING – STRETCHING AND INSTALLING FIRST STAPLES

Step 18

16 x 20 Canvas Stretching - Step 18 - Align stretcher bars with image outline

Starting with the right side, carefully lift the canvas print and ensure the image is wrapped around the front face of the stretcher bar. Repeat this on the opposite side, moving the stretcher assembly left or right until you see the image wrapping equally around both sidebars.


Step 19

16 x 20 Canvas Stretching - Step 19 - Mark canvas with pencil along stretcher bars

Once you are sure that you have centered the stretcher bar about the printed image, draw a reference line along each side as shown. This reference line will be helpful later if the stretcher assembly moves out of position and you need to realign it.


Step 20

16 x 20 Canvas Stretching - Step 20 - Check that pencil mark aligns with image

As we did in Step 18 for the side positioning, we want to center the stretcher bar assembly along the top and bottom bars. Carefully lift the canvas print and ensure the image is wrapped around the front face of the bottom stretcher bar. Repeat this for the top stretcher bar, moving the stretcher assembly up or down as needed until you see the image wrapping equally around the top and bottom bars.


Step 21

16 x 20 Canvas Stretching - Step 21 - Mark remaining canvas on all side with pencil along stretcher bars

Once you are sure that you have centered the stretcher bar about the printed image, draw a reference line along each side as shown. We have now centered the stretcher bar assembly in both the vertical and horizontal directions concerning the printed image. We are ready to begin the canvas stretching, wrapping, and stapling processes.

16×20 CANVAS STRETCHING – STRETCHING AND INSTALLING FIRST STAPLES

Step 22a

16 x 20 Canvas Stretching - Step 22a - Prepare staple gun for canvas attachment to stretcher bars

For this example, we have selected 1/4″ staples. Load your staple gun, so you stay supplied with staples partway through the following steps.


Step 22b

16 x 20 Canvas Stretching - Step 22 - Wrap canvas around first stretcher bar

Starting with the top stretcher bar, wrap the giclee canvas print around the stretcher bar as shown. Ensure the stretcher assembly has not moved out of the reference lines we drew earlier.


Step 23

16 x 20 Canvas Stretching - Step 23 - Staple canvas in center of first stretcher bar

Holding the staple gun squarely on the canvas and stretcher bar, staple the canvas to the stretcher bar in the center of the bar as shown.


Step 24

16 x 20 Canvas Stretching - Step 24 - Inspect staple and ensure it seated into stretcher bar

Check that your assembly looks like this – having one staple in the center of the top stretcher bar.


Step 25

16 x 20 Canvas Stretching - Step 25 - Wrap canvas on opposite side and grip with canvas pliers

While firmly holding the canvas pliers, grip the canvas in the center of the bottom stretcher bar, opposite from the first staple in the center of the top stretcher bar.


Step 26

16 x 20 Canvas Stretching - Step 26 - Apply tension using canvas pliers

Using the stretcher bar as leverage, rock the canvas pliers forward (compare images from steps 25 and 26) until the canvas has stretched – notice that the canvas is tightly wrapped around the stretcher bar.


Step 27

16 x 20 Canvas Stretching - Step 27 - Firmly hold canvas in position with thumb

Before releasing the canvas pliers, press your thumb onto the canvas. Holding your thumb in this manner will maintain canvas tension during staple insertion.


Step 28

16 x 20 Canvas Stretching - Step 28 - Staple canvas to center of stretcher bar

While firmly pressing your thumb on the canvas, insert one staple while maintaining tension. Hold the staple gun squarely on the canvas and stretcher bar and staple the canvas to the stretcher bar in the center of the bar as shown.


Step 29

16 x 20 Canvas Stretching - Step 29 - Inspect second staple to ensure its properly seated

Check that your assembly looks like this – having one staple in the center of the bottom stretcher bar.


Step 30

16 x 20 Canvas Stretching - Step 30 - Look for canvas tension ridge between first two staple points

Once you have inserted the first two staples into the top and bottom stretcher bars as shown you should notice a slight tension pull on the canvas between the two staple points (i.e., points A and B.)


Step 31

16 x 20 Canvas Stretching - Step 31 - Using canvas pliers stretch and staple canvas to center of third stretcher

Using the canvas pliers, stretch the canvas starting on the left side and hold tension, applying firm finger pressure. (…I am keeping the pliers away from my body, and this provides less stretching and leveraging control. Because I’m not applying tension for the first side staple, I chose to use the pliers this way. However, when you are stretching opposing sides it is recommended to hold the pliers so that they are facing toward your body as shown in images 25 through 28)


Step 32

16 x 20 Canvas Stretching - Step 32 - Inspect that staple is fully seated in stretcher bar

Insert one staple in the center of the side stretcher bar.


Step 33

16 x 20 Canvas Stretching - Step 33 - Stretch and staple canvas on fourth side

Repeat the stretching and stapling process as shown in steps 25 through 28. Be sure to firmly hold the canvas with your thumb before removing the pliers.


Step 34

16 x 20 Canvas Stretching - Step 34 - Inspect canvas for droops and sags

Be sure to stretch the canvas when stapling opposing sides, so it does not droop or sag. Our assembly should now have one staple placed directly in the center of each stretcher bar, as shown.


Step 35

16 x 20 Canvas Stretching - Step 35 - Ensure canvas image is square with stretcher bar assembly

Flip over the assembly to look at the printed image on the front. Check that the image is centered vertically and horizontally – you should see the image wrapping equally around all sides, and no ‘white’ border should be visible along the front face. Check that the image has not rotated clockwise or counter-clockwise so that it is no longer square with the stretcher bars. Also, check that the canvas is not overly loose or sagging. In the following steps, we will tighten the canvas as we stretch, wrap, and insert the remaining staples, but now is the time to remove the staples and make adjustments if the position of the image is off or the canvas is very loose and sagging.

16×20 CANVAS STRETCHING – STRETCHING AND INSTALLING REMAINING STAPLES

Step 36

16 x 20 Canvas Stretching - Step 36 - Using canvas pliers stretch from first staple

Beginning with the top stretcher bar (1), stretch the canvas using canvas pliers and hold tension by applying pressure with your thumb.


Step 37

16 x 20 Canvas Stretching - Step 37 - Stretch and staple to end of first stretcher bar

Insert staples starting from the center staple and moving left with each new staple until you reach the left stretcher bar, as shown. Use canvas pliers as needed.


Step 38

16 x 20 Canvas Stretching - Step 38 - Stretch canvas around second stretcher bar

Moving to the bottom stretcher bar (2), stretch the canvas using canvas pliers and hold tension by applying pressure with your thumb.


Step 39

16 x 20 Canvas Stretching - Step 39 - Stretch and staple to end of second stretcher

Insert staples starting from the center staple and moving right with each new staple until you reach the right stretcher bar as shown. Use canvas pliers as needed.


Step 40

16 x 20 Canvas Stretching - Step 40 - Stretch and staple to end of third and fourth stretchers

Repeat the previous step for the left (3) and right (4) stretcher bars in that order. Remember to start from the center staple and move toward the arrows (as shown) as you staple the remaining two sides. Use canvas pliers as needed.


Step 41

16 x 20 Canvas Stretching - Step 41 - Stretch canvas and staple at other end of first stretcher

Now begin applying more tension when stretching the canvas using the pliers. Always have the canvas pliers facing away from your body during the final stretching and stapling steps for maximum tension and leveraging control. Starting closest to the center staple on the bottom stretcher bar (1), stretch the canvas, maintain pressure with your thumb, and insert two or three adjacent staples starting from the center staple and moving left.


Step 42

16 x 20 Canvas Stretching - Step 42 - Moving toward end, stretch and staple

Move slightly to the left of the staples you just inserted in step 41, use the canvas pliers to pull the canvas tight, apply thumb pressure to maintain canvas tension, and insert two or three more adjacent staples moving in the left direction toward the left stretcher bar.


Step 43

16 x 20 Canvas Stretching - Step 43 - Moving toward end, stretch and staple

Reposition the canvas pliers closer to the left stretcher bar, pull the canvas tight using canvas pliers, maintain pressure with your thumb, and insert several adjacent staples.

Repeat this process until you reach the left stretcher bar.


Step 44

16 x 20 Canvas Stretching - Step 44 - Inspect that all staples are fully seated

After inserting staples along the bottom (1) stretcher bar, your assembly should look like this.


Step 45

16 x 20 Canvas Stretching - Step 42 - Repeat stretching and stapling on remaining sides

Repeat steps 41 through 44 for the top (2), left (3), and right (4) sides – in that order until your assembly looks like this.


Step 46

16 x 20 Canvas Stretching - Step 46 - Test tension by tapping canvas listen for drum sound

A good test to see if you stretched the canvas enough is to tap the center of the canvas with your finger and listen for a drum-like sound. If the canvas is improperly stretched and loose, it will not have this sound and flop around as you tap it. Also, if you see ripples in the canvas, you have an uneven tension problem – the canvas is not tight.


Step 47

16 x 20 Canvas Stretching - Step 47 - Fold and Wrap canvas around corner

Now we must fold and secure the four corners. Hold the corner of the canvas material as shown.


Step 48

16 x 20 Canvas Stretching - Step 48 - Ensure canvas print is stretched tight over corner

While applying tension, wrap the corner around the stretcher bar as shown so that the fold is on the side of the assembly. The fold should run at a 45-degree angle, as shown.


Step 49

16 x 20 Canvas Stretching - Step 49 - Hold wrapped canvas print tightly on back

While applying tension on the canvas material, fold it around the back face and hold it securely in the position shown in preparation for stapling.


Step 50

16 x 20 Canvas Stretching - Step 50 - Staple folded corner to stretcher bar

While holding the corner in position, insert several staples as shown.


Step 51

16 x 20 Canvas Stretching - Step 51 - Staple folded corners on remaining sides

Repeat steps 47 through 50 on the remaining three corners. Be careful that your folded edges are always on along the side stretcher bars. Your finished assembly should look like this when viewed from the back. Use your hammer to insert all staples fully.


Step 52

16 x 20 Canvas Stretching - Step 52 - Inspect and Finished

You have completed the 16×20 canvas stretching tutorial. Congratulations!

Concluding Thoughts

Please see our 8×10 Canvas Stretching Tutorial, a companion article to this 16×20 Canvas Stretching Tutorial, and learn about using canvas stretching pliers.

8×10 Canvas Stretching Tutorial by John O’Keefe Jr.

This 8×10 canvas stretching tutorial focuses on a giclee print on canvas. However, the steps can also be applied to any small-sized canvas, whether raw, primed, or painted. I provide tutorials like this for free because I feel that all of us should be able to enjoy creating art without all the extra “costs” that many would charge for this level of information.

8×10 Canvas Stretching – Materials and Tools

Step 1

8 x 10 Canvas Stretching - Step 1 - Assemble all materials

Before starting, Assemble all materials and tools for the 8×10 canvas stretching tutorial.

  1. Cloth Work Surface
  2. Giclee Print
  3. Pre-Made Stretcher Bars
  4. Square Ruler
  5. Mallet
  6. Small Hammer (not shown)
  7. Flathead Screwdriver (not shown)
  8. Staple Gun
  9. 1/4″ Staples

Canvas Stretching – Assemble the Stretcher Bars

Step 2

8 x 10 Canvas Stretching - Step 2 - Dry-Fit first two stretcher bars

In this example, we used pre-made stretcher bars that come ready to assemble. These stretcher bars have cut grooves at each end for mating and interlocking to adjacent bars. You may need to sand rough edges on pre-made stretchers because the cutting tools used during manufacturing may leave wood burrs and sharp edges.


Step 3

8 x 10 Canvas Stretching - Step 3 - Fully seat first two stretcher bars

Make sure that you fully seat the two stretcher bar ends. You must still mate the two bars fully if you see a gap along the seam where the ends meet.


Step 4

8 x 10 Canvas Stretching - Step 4 - Fully seat remaining stretcher bars

In this view, see all four stretcher bars mated together. However, we must ensure that all four corners of this assembly are square. (i.e., A, B, C, & D)


Step 5

8 x 10 Canvas Stretching - Step 5 - Use square to measure squareness

We must check each corner using a square ruler to ensure they are square. It is a critical step because if your final assembly is not square, it may not fit into your frame.


Step 6

8 x 10 Canvas Stretching - Step 6 - Fully seat square onto stretcher bar corners

Hold the square ruler as shown and check that both inside edges of the ruler run flush along the surface of each stretcher bar. If the ruler lifts off one side (not running flush along one surface while being thoroughly flush on the other), you are not square on that corner.


Step 7

8 x 10 Canvas Stretching - Step 7 - Adjust with mallet if out-of-square

Using a mallet, gently tap the corner(s) to make adjustments.


Step 8

8 x 10 Canvas Stretching - Step 8 - Recheck for squareness

Recheck corners until they are all square. Now you are ready to start the canvas mounting process.

Canvas Stretching – Prepare for Stapling

Step 9

8 x 10 Canvas Stretching - Step 9 - Clean work surface before laying down canvas print

Before laying down your giclee canvas print, make sure there are no debris or wood pieces (that may have fallen off during stretcher bar assembly) that could damage the printed surface. Use a soft cloth work surface to minimize the chances of causing minor scratches to your giclee canvas print.


Step 10

8 x 10 Canvas Stretching - Step 10 - Inspect canvas print for damage before proceeding

Lay down your print (face up) and make a final close examination to ensure there is no damage from the print supplier.


Step 11

8 x 10 Canvas Stretching - Step 11 - Place canvas print face down on work surface

At this point, turn over your giclee print so that the image is face down. You are now ready to position your stretcher bar assembly.


Step 12

8 x 10 Canvas Stretching - Step 12 - Place assembled stretcher bars on canvas print

Place your stretcher bar assembly over your giclee canvas print as shown.


Step 13

8 x 10 Canvas Stretching - Step 13 - Align stretcher bars with image outline

Starting with the right side, carefully lift the canvas print and ensure that the image wraps around the front face of the stretcher bar. Repeat this on the opposite side, moving the stretcher assembly left or right until you see the image wrapping equally around both sidebars.


Step 14

8 x 10 Canvas Stretching - Step 14 - Mark canvas with pencil along stretcher bars

Once you have centered the stretcher bar about the printed image, draw a reference line along each side as shown. This reference line will be helpful later if the stretcher assembly moves out of position and you need to realign it.


Step 15

8 x 10 Canvas Stretching - Step 15 - Check that pencil mark aligns with image

As we did in Step 13 for the side positioning, we want to center the stretcher bar assembly along the top and bottom bars. Carefully lift the canvas print and ensure that the image wraps around the front face of the bottom stretcher bar. Repeat this for the top stretcher bar, moving the stretcher assembly up or down as needed until you see the image wrapping equally around the top and bottom bars.


Step 16

8 x 10 Canvas Stretching - Step 16 - Check pencil marks all around with canvas print image

Once you have centered the stretcher bar about the printed image, draw a reference line along each side as shown. The stretcher bar assembly is now centered in the printed image’s vertical and horizontal directions. We are ready to begin the canvas stretching, wrapping, and stapling processes.

8×10 Canvas Stretching – Stretching and Installing First Staples

Step 17

8 x 10 Canvas Stretching - Step 17 - Prepare staple gun for canvas attachment to stretcher bars

For this example, we have selected 1/4″ staples. Load your staple gun, so you stay supplied with staples partway through the following steps.


Step 18

8 x 10 Canvas Stretching - Step 18 - Fold canvas print over first stretcher bar

Starting with the top stretcher bar, wrap the giclee canvas print around the stretcher bar as shown. Ensure the stretcher assembly has stayed in the reference lines we drew earlier.


Step 19

8 x 10 Canvas Stretching - Step 19 - Staple canvas print over first stretcher bar

Holding the staple gun squarely on the canvas and stretcher bar, staple the canvas to the stretcher bar in the center of the bar as shown.


Step 20

8 x 10 Canvas Stretching - Step 20 - First staple should be in the center of stretcher bar

Check that your assembly looks like this – having one staple in the center of the top stretcher bar.


Step 21

8 x 10 Canvas Stretching - Step 21 - Seat staple with hammer if not fully inserted

Sometimes the staple gun is not held square to the canvas and stretcher bar resulting in a partially inserted staple. Lightly tap the staple with a hammer until fully inserted.


Step 22

8 x 10 Canvas Stretching - Step 22 - Fold canvas print over opposite stretcher bar

We are now ready to tightly pull and wrap the giclee canvas print around the bottom stretcher bar. Using your hand strength, stretch the canvas, wrap it around the bottom stretcher bar, and hold it securely with your thumb (as shown) in preparation for stapling.


Step 23

8 x 10 Canvas Stretching - Step 23 - Staple canvas print over opposite stretcher bar

While holding your thumb in place, insert one staple in the center of the bottom stretcher bar. Once you have added the first two staples into the top and bottom stretcher bars, you should notice a slight tension pull on the canvas between the two staple points (i.e., points A and B.)


Step 24

8 x 10 Canvas Stretching - Step 24 - Fold and staple canvas print over third stretcher bar

As we did in the previous steps for the top and bottom, now we must secure the left and right sides. Starting with the left side, stretch, wrap, and hold the canvas securely in preparation for stapling. (Not shown: Insert one staple in the center of the left stretcher bar.)


Step 25

8 x 10 Canvas Stretching - Step 25 - Fold and staple canvas print over fourth stretcher bar

As we did in the previous steps, stretch, wrap, and staple the right side. When stapling opposing sides, you pull the canvas, so it does not droop or sag. Our assembly should now have one staple placed directly in the center of each stretcher bar, as shown.


Step 26

8 x 10 Canvas Stretching - Step 26 - Flip assembly and inspect the image is square with stretcher bars

Flip over the assembly, so you look at the printed image on the front. Check that the image is centered vertically and horizontally – you should see the image wrapping equally around all sides, and no ‘white’ border should be visible along the front face. Check that the image has not rotated clockwise or counter-clockwise so that it is no longer square with the stretcher bars.

Also, check that the printed image is tight enough and sagging. In the following steps, we will tighten the canvas as we stretch, wrap, and insert the remaining staples, but now is the time to remove the staples and make adjustments if the position of the image is off or the canvas is very loose and sagging.

8×10 Canvas Stretching – Stretching and Install Remaining Staples

Step 27

8 x 10 Canvas Stretching - Step 27 - Staple first stretcher from center to end

Beginning with the top stretcher bar (1), insert staples starting from the center staple and moving left with each new staple until you reach the left stretcher bar as shown.


Step 28

8 x 10 Canvas Stretching - Step 28 - Staples remaining stretchers from center to end

Repeat the previous step for the bottom (2), left (3), and right (4) stretcher bars in that order. Remember to start from the center staple and move toward the arrows (as shown) as you staple the remaining three sides.


Step 29

8 x 10 Canvas Stretching - Step 29 - Staple all four stretchers in opposite direction

Now we are ready to pull and stretch the canvas for the remaining unsecured areas. Starting with the top (1) stretcher bar, PULL THE CANVAS SNUG, hold it with your thumb, and staple it from the center to the right stretcher bar as shown. Repeat this process for the bottom (2), left (3), and right (4) stretcher bars in that order.

IMPORTANT: You should notice that the canvas has more tension across the front face. It should not sag, droop, or have ripples along the surface. If these conditions exist, you must apply more pressure during pulling and stapling. If you determine that your canvas was not properly stretched, you may need to remove all the staples and repeat the stretching and stapling processes. Hearing the sound of a drum when you tap your finger on the back of the canvas indicates good tension. It may sound more like a resounding thud on a small hand-stretched canvas (as shown in this tutorial).

Canvas Stretching – Folding and Stapling Corners

Step 30

8 x 10 Canvas Stretching - Step 30 - Fold and Wrap canvas around corner

Now we must fold and secure the four corners. Hold the canvas material, as shown.


Step 31

8 x 10 Canvas Stretching - Step 31 - Ensure canvas print is stretched tight over corner

While applying pressure, wrap the corner around the stretcher bar as shown so that the fold is on the side of the assembly. The fold should run at a 45-degree angle, as shown.


Step 32

8 x 10 Canvas Stretching - Step 32 - Hold wrapped canvas print tightly on back

While applying pressure on the canvas material, fold it around the back face and hold it securely in the position shown in preparation for stapling.


Step 33

8 x 10 Canvas Stretching - Step 33 - Staple folded corner to stretcher bar

While holding the corner in position, insert several staples as shown.


Step 34

8 x 10 Canvas Stretching - Step 34 - Repeat folding and stapling on remaining corners

Repeat steps 30 through 33 on the remaining three corners. Be careful that your folded edges are always on along the side stretcher bars. Your finished assembly should look like this when viewed from the back. Now use your hammer to insert all staples fully.


Step 35

8 x 10 Canvas Stretching - Step 30 - Inspect and Finished

You have completed the 8×10 canvas stretching tutorial. Congratulations!

Concluding Thoughts

Please see our 16×20 Canvas Stretching Tutorial, a companion article to this 8×10 Canvas Stretching Tutorial, and learn about using canvas stretching pliers.